The flight controller features a builtin 433mhz oplink modem and uses the standard. Navigation and monitoring system primarily intended for marine operation in small boats. The positive vcc and negative gnd pins are indicated on this diagram and. The revo flight controller features state of the art hardware and software, backed by the. This video shows how to configure the cc3d revolution flight. Openpilot revolution and revomini copter documentation. The instructions consist of hardware and software side. The oplink mini module requires three wires for normal.
The software and settings are loaded through usb connector and nohassle update. The flight controller features a builtin 433mhz oplink modem and uses the standard openpilot footprint so has the same dimensions and mounting holes as the openpilot cc, cc3d, gps, osd and pipx boards. Openpilot oplink mini cc3d revo universal transceiver tx rx module integrating remote controller sale. Dimensions openpilot products use the standard openpilot footprint, and hence has the same dimensions and mounting holes as the openpilot revo, gps, osd and pipx boards. The oplink is a radio transceiver backed by an arm32 powered digital packet processor specifically designed for the openpilot project, it was originally developed under the codename. The openpilot revolution board, also called revo, is a new breed of autopilot using the stm32f4 series, 210mips arm microcontroller. You use this software to load the firmware and setup your cc3d revolution. This version supports the coptercontrol, cc3d, atom, revolution, revolution nano, platinum gps v9 and oplink modems.
Huson rc cc3d revolution video 3 oplink module setup. Set up the hardware side first and then do the necessary hardware configuration changes. Openpilot cc3d revolution technical description cpu cpu is the stm32f405rgt6 chip, with arm cortexm4 core at 210mips, fpu, and saturation arithmetics dsp functions. Although the hardware is the same, several software or firmware revisions exist. The diagram also shows other optional equipment such as gps module, oplink. Oplm vehicle control link librepilotopenpilot wiki 0. Revominis oplink port can be used for external spi periphereals connection arbitrary pins can be used for various connections like 2nd gps, additional pwm outputs etc.
The main focus of this release is to bring back support for cc3d and a general rebranding of the gcs. Openpilot aspires to provide the functionality found in a normal marine chartplotter, for free. If you have not done binding yet for the oplink modules, do that first using oplm binding and basic telemetry page instructions, and return to this tutorial after that. Openpilot cc3d revolution revo 32bit f4 based flight controller wintegrated 433mhz oplink. Full configurations instructions can be found in the openpilot manual.
The chip features a range of builtin hardware modules that can bo programmed once and function independently, requiring. It can fly any airframe from fixed wing to an octocopter and is configured and monitored using the openpilot ground control station gcs software. Openpilot revolution flight controller guide guides dronetrest. Select 57600 or another speed that your bluetooth module is configured to as speed.
Note that the revolution board has an oplink built into the flight controller. Find file copy path openpilot hardware production oplink mini oplink mini schematic. Navigate to the hardware tab on the configuration page in the openpilot gcs. Bluetooth setup for telemetry librepilotopenpilot wiki. This document will describe the necessary hardware and software setup to connect an. You will need to supply power and control data from the transmitter to the oplink module. Quick howto video all boards erased oplink rc side as coordinator.
The software and settings are loaded through usb connector and nohassle update function in the gcs ground control station. Modem the board features builtin 433mhz oplink modem. Diy mini quadcopter w openpilot cc3d wiring, configuration, and garage maiden duration. This is important, as it contains a hardware floating point unit fpu, which is a huge advancement for hobbyclass autopilots. Openpilot oplink mini ground station 433 mhz hobbyking. The positive vcc and negative gnd pins are indicated on this diagram and the board. Revolution or sparky2 board no need extra wiring, oplink modem is already integrated and wiring is done internally. Make sure that you have the same openpilot firmware versions on both the flight controller and oplink modem. This version supports the coptercontrol, cc3d, atom, and revo as well as the oplink modems. Openpilot will run natively under both windows and linux. Pipxtreme and there are many artifacts that still reflect this.
Link to librepilot website to download the software for your computer. Openpilot oplink mini cc3d revo universal transceiver tx. The oplink module will get its power from the flight controllers external power, so unlike revolution, the modem will not get powered on by just plugging in the usb to the flight controller. Find file copy path fetching contributors cannot retrieve contributors at this time. Antenna connection socket for onboard oplink modem. The software and settings are loaded through usb connector and nohassle.
985 1471 242 146 319 974 1350 1505 330 1289 551 845 1407 285 496 893 1244 510 195 1386 325 246 164 1171 585 533 903 501 867 1166 845 1529 73 165 481 1458 1077 1070 754 1400 465 1285